1.        GETTING STARTED: Check the BerryAlloc boards and make sure that the surface has no transport damaging before you start. After cleaning the subfloor you can roll over the plastic foil and underlay material. The plastic foil has to overlap minimum 20 cm. 

2.          FIRST ROW: Start installation of the boards in the left-hand corner, with the tongue side against the wall. Make sure you place the short side of the board 8-10 mm from the wall. The long-side can be pushed into place when three rows have been installed (Maintain a distance of 8-10 mm). If the wall is uneven, the floorboards must be adapted to its contours. Remove the first row. Cut the boards as required and then relay them by sliding them in at an angle.

3.       END SECTION:Position the end section of the next floorboard at an angle to the first one, then lay down. Complete the first row in the same matter.

4.        Place the final floorboard face down with the short side without a locking strip towards the wall. The distance to the wall must be 8-10 mm. Mark where the floorboard is to be cut.

5.       CUTTING THE BOARDS: Place the board face down on the work surface and cut to size using a jig-saw. If you are using a hand saw, ensure that it is fine-toothed and cut the board face up.

6.        STARTING THE SECOND ROW: Use a cut piece of board at least 30 cm long from the previous row to start the next row. If this piece is too short, start with a new board cut in half. Always ensure that the end joints are staggered at least 30 cm.

7.         CONTINUE LAYING THE FLOOR: Place the floorboard at an angle against the floorboard in the previous row, press forward and fold down at the same time.

8.          Place the short end of the floorboard at an angle against the previously installed floorboard and fold down. Ensure that the board is positioned on the integral locking strip of the floorboard in the previous row.

9.        Lift up the board (along with the board that was previously laid in the row) by about 25 mm and press it against the previous row. Bring the panel down again as soon as the boards are positioned tightly together. Do not press the board fully down. After all boards in the row have been put in place, press all boards flat against the subfloor (or walk over them to achieve the same effect) before starting on the next row.

10.      TO LAY THE LAST ROW: Measure and cut the board. Leave 8-10 mm distance to the wall.

11.      HOLES FOR PIPES: Measure the diameter of the pipe and drill a hole that is 10 mm larger. Saw off a piece as shown in the picture and lay the board in place on the floor. Then lay the sawen-off piece in place.

12.      DOOR MOULDINGS AND SKIRTINGS: Lay a board (with the decorative side down) next to the door moulding and saw as shown in the picture. Then slide the floorboard under the moulding.

Berryalloc Magic cleaner kit

This unique cleaning system smoothly cleans every laminate floor, whether dry or wet. The kit contains a floor wiper with an adjustable blade, microfibre cloths and a fresh, fruity laminate cleaner. It's a complete cleaning set and turns cleaning your BerryAlloc laminate flooring into child's play.

Berryalloc Laminate spray

An easily adjustable spray that cleans all laminate surfaces without streaking and that leaves behind a light and pleasant grapefruit scent. It has an antistatic and antibacterial action and so is well suited to spaces where hygiene is of the utmost importance. Rinsing is not necessary.

Berryalloc Laminate cleaner

Guarantees that your BerryAlloc laminate floor stays in perfect condition and is suitable for both first-time maintenance and regular use. Suitable for spaces where hygiene is of the utmost importance. Rinsing is not necessary.

Berryalloc repair kit

From now on you can perform minor repairs to your laminate floor with the help of this handy repair kit. Remove the loose pieces, apply the filler material to the mixing palette, mix the colour until you achieve the desired shade and finish it using the abrasive pad. The BerryAlloc Repair kit comes in two different versions - one for light floors and the other for dark floors.